Home
General Rules
Limited Weld
Modified Compact Rules
Adult Stock Compact
Youth Compact Heat
Two Man Truck Team
Mini Van Rules
Pro Class
Power Wheels
 


2015 Youth Compact Class

1.       ALL CARS MUST REMAIN STOCK UNLESS OTHERWISE NOTED ON THESE RULES!!

2.       You must comply with all safety and general rules. (Must be 12-16 years old without a drivers license)

3.       Types of cars

a.       Any FWD car with 109” wheel base MAX!

b.      Must be 4 or 6 cylinder

c.       NO rear wheel drive cars!

4.       Car preparations

a.       All glass, plastic, fiberglass, chrome molding, door handles, mirrors, etc. must be removed.

b.      All flammable material must be removed, such as carpet, headliners, and back seats.

c.       Only one battery is allowed. Battery must be mounted on passenger floor board or behind passenger seat and covered.

d.      Original gas tank must be removed and cannot be reused inside of the car. Must mount a metal boat tank or fuel cell in center of backseat area and must be covered.

5.       Cages

a.       4 point cage is MANDATORY!!! Maximum 4” square, round, or C-channel permitted.

b.      Halo bar must mount to rear seat bar or side bars and must run straight up and over roof.

c.       4 square mounting plates for cage are allowed. MAX size 8” X 8” X ¼”

d.      One gas tank protector is allowed. 24” wide MAX. May have two down legs off protector to floor sheet metal.

e.      Cage may be gusseted. (These are kids’ cars so please weld them in good)

f.        Must have two safety straps from roof to cowl or dash bar.

g.       May have a MAX of two rear window bars. MAX size 2” square or round pipe or 3” wide 3/8” flat plate. Can be welded at a MAX of 6” on roof and 6” within deck lid/speaker deck seam.

h.      We will allow anything within the driver’s compartment. Please call with any questions.

6.       BODY

a.       All doors may be welded solid using 3”X 3” X ¼” plate.

b.      No inner body seam welding.

c.       Both front doors must be reinforced with ¼” plate.

d.      Hoods must have 8” X 8” hole opening. May bolt around opening using 3/8” bolts max.

e.      Trunks and tailgates may be welded solid using 3” X 3” X ¼” plate.

f.        NO tucking or wedging allowed.

g.       Rear quarters must remain at factory height

h.      May dip trunk down 6” max, but the quarters cannot be moved. Center of trunk cannot be more than 6” below quarters.

i.         Must have an 8” X 8” hole in trunk lid. May bolt around opening using 3/8” bolts max.

j.        Body line creasing is allowed.

k.       Wheel lips can be cut and folded (cannot be welded) MAY bolt wheel lips using four 5/8” bolts.

l.         Sheet metal patching for rust is allowed, but must be factory thickness (Call first)

7.       Solid suspension is allowed. (Cars do not have to bounce) (Call with questions)

8.       Bumpers

a.       Any year car bumper is allowed. NO homemade bumpers.

b.      NO LOADED BUMPERS!!

c.       May seam weld the bumper, but all factory holes must remain open.

d.      May have an 8” bumper shock 2” X 2” square or round.

e.      May have an 8” X 8” X 3/8” plate for mounting bumpers.

9.       Wheels and tires

a.       Any tread design and any ply tire is allowed.

b.      Screwed, glued, doubled, tripled, and foam filled tires allowed.

c.       Valve stem guards, rim guards, bead locks, side wall protectors and solid wheels allowed.

10.   NO PLATING FRAMES!!

11.   A parent or guardian is required with a valid driver’s license or picture ID. There will be a notary present the day of the show to notarize consent and a minor release form.

12.   A parent or an adult MUST ride with the driver of the car during the heart.

13.   IF IT’S NOT STATED IN THE AVOVE RULES, DON’T JUST DO IT!!  EXCESSIVE WELDING WILL RESULT IN EXCESSIVE CUTTING! IF NOT SURE ABOUT SOMETHING, PLEASE CALL FIRST!!!

FOR ANY QUESTIONS/CONCERNS REGARDING RULES CONTACT


LUKE SPROUSE (330) 708-3214

TONY COOPER (330) 383-6131

BRIAN MCCULLEY (330) 853-1072







Top